Cobra Electronics Automobile Alarm Series 3100 User Manual

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS  
REV. 00  
PETROL  
DIESEL  
X
DAEWOO  
NUBIRA  
98 ®  
MAKE  
MOD.  
YEAR  
Position the compact alarms and the sirens in the engine compartment near the  
left lateral headlamp. Position the modular systems and the modules under the  
dashboard, drivers side.  
ALARM/SIREN  
POSITION  
POWER SUPPLY  
+ 30: connect to the 2,5mm2 RED wire located at the rear of the left lateral frame,  
drivers side.  
- 31: connect with an eyelet cable terminal to one of the fastening bolt of the  
dashboard.  
Connect to the 1 mm2 BLUE and LIGHT BLUE wires located in the wiring  
harness and coming out of the 22 way yellow connector located on the support of  
the connector holder, above the fuse box behind the left lateral frame, drivers  
side.  
DIRECTION INDICATORS  
ELECTRIC WINDOWS  
Positive control signal  
Front window, driver’s side:  
cut the BLUE wire directly outgoing from the switch of the window to the inner  
drivers side door.  
Front window, passenger’s side:  
cut the 1,5 mm2 LIGHT BLUE wire.  
Rear window, driver’s side:  
cut the 1,5 mm2 BROWN wire.  
Rear window, passenger’s side:  
cut the 1,5 mm2 GREEN wire located in the wiring harness coming out of the  
drivers side door.  
CENTRAL DOORS LOCKING  
Negative control signal  
Connect to the LIGHT BLUE wires with WHITE reference located at the position  
nr. 7 (lock) and the YELLOW at the position nr. 1 (unlock), in the 9 way white  
connector of the central door locking unit located at the rear of the left lateral  
frame, drivers side.  
Note: for the vehicles without original key less entry, please refer to  
diagram nr. 42 for the serie Bridge antithefts or refer to diagram nr.42A for  
serie 3100 antithefts.  
The vehicle has an original equipment immobiliser that may be enabled  
immediately when the switchboard is switched off.  
IMMOBILISATION POINT  
Install an additional switch on the front headlamp support plate.  
BONNET SWITCH  
DOORS SWITCH  
Connect to the 0,5 mm2 WHITE wire located in the wiring harness coming out of  
the 16 way white connector, on the support of the connector holder, above the  
fuse box behind the left lateral frame, drivers side.  
Connect to the 0,5 mm2 PINK wire with BLACK reference located in the wiring  
harness and coming out of the 16 way white connector located on the support  
mentioned above.  
BOOT SWITCH  
danub98gbb.doc  
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed  
as per the instructions given on the product installation manual.  
 
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS  
FITTING DIAGRAM N°42A  
REV. 00  
Serie 3100 antitheft  
ORANGE/WHITE  
VIOLET/WHITE  
White connector coming out of the central  
doors locking unit.  
VIOLET  
ORANGE  
3
8
1 2  
4
9
5
6 7  
Negative control signal  
For the versions without original radio control the positions Nr. 1 and Nr. 7 of the  
white connector of the central doors locking are free, so insert suitable fastons.  
danub98gbb.doc  
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed  
as per the instructions given on the product installation manual.  
 

Craftsman Lawn Mower 37623 User Manual
Creda Cooktop W810 User Manual
Cuisinart Blender ICE 40 User Manual
Cuisinart Oven 89220 User Manual
Curtis Flat Panel Television LCP4210 User Manual
Curtis Flat Panel Television RT705A User Manual
Digital Antenna Network Card DA298 User Manual
Extron electronic Network Card IPA T RLY4 User Manual
Fujitsu Battery Charger FJBC GP User Manual
GE Air Conditioner AED10 User Manual